In this article in the next paragraph you'll find a bunch of great advice regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard project. If the old bathtub is readily accessible, the job can relocate easily; if you need to open a wall surface to remove the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and embeded in the new one. Make certain you have actually qualified yourself for the task as well as are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed job, it is much better to think about using one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This article will certainly aid you mount a brand-new tub in your shower room if you have already acquired a brand-new bathtub as well as do not require to change the plan of your previous water supply pipelines.
Your devices as well as product checklist must consist of the following:
- New Bathtub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Degree
- Pliers
- Flexible Wrench
- Putty Blade
- Screwdriver
- Cold Knife
- Measuring tape
- Pipeline Caps
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap and also the sink. Protect the faucet in place with the maker given backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind should be linked to the tap ends first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing the two wood boards under its feet, put the bath tub in the required setting. The wooden boards are valuable in evenly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bathtub until the level checks out degree.
To mount taps, fit all-time low of the furthest adaptable tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water supply and inspect all joints as well as brand-new pipework for leaks as well as tighten them if required. Load the bath tub as well as likewise examine the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait up until the tub has been used a minimum of when as this will resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bath must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to stop stress on the tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture fairly early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about Tools You Need to Install a New Bathtub ? Write feedback further down. We'd be pleased to see your responses about this blog. In hopes that you come back again in the near future. Remember to set aside a second to distribute this article if you enjoyed it. Many thanks for your time. Don't forget to check up our site back soon.
Book A Free Estimate
Comments on “Can I Install A Bath Tub Myself?”